Impressum | Datenschutz | Shop | DIY | TT @ Twitter | TT-Cabs
Anzeigen der neuesten Beiträge

My SLO Clone Build

  • 58 Antworten
  • 30151 Aufrufe

0 Mitglieder und 1 Gast betrachten dieses Thema.

*

Offline FourT6and2

  • Full Member
  • ***
  • 46
Re: My SLO Clone Build
« Antwort #30 am: 20.07.2014 03:49 »
Most of the power section is done. Once the preamp is wired up I can finalize the remaining connections on the power board. It's not as tidy as I really want. But there are a lot of wire runs in the SLO. Good thing they're all covered by the power PCB :) And I spliced in the lead from the OT to the HT Fuse.








*

Offline Jürgen

  • YaBB God
  • *****
  • 401
Re: My SLO Clone Build
« Antwort #31 am: 20.07.2014 04:06 »
 :topjob:

*

Offline FourT6and2

  • Full Member
  • ***
  • 46
Re: My SLO Clone Build
« Antwort #32 am: 21.07.2014 09:02 »
Elevated heater mod wired up. This part was like playing that Operation board game.


*

Offline FourT6and2

  • Full Member
  • ***
  • 46
Re: My SLO Clone Build
« Antwort #33 am: 22.07.2014 15:53 »
Damn, power tube sockets took a long time. But they're finally done. Just need to add some heat shrink to the grid stoppers. Next steps will be the loop jacks, impedance selector, and then I can move on to the preamp board wiring and I'll be done.










*

Offline mc_guitar

  • YaBB God
  • *****
  • 1.379
Re: My SLO Clone Build
« Antwort #34 am: 22.07.2014 17:41 »
Hello,

Looks incredibly tidy! thumbs up for your superb work!!
 :topjob:

Cheers Michael
Zwei Dinge sind unendlich, das Universum und die menschliche Dummheit, aber bei dem Universum bin ich mir noch nicht ganz sicher...(Albert Einstein)

*

Offline FourT6and2

  • Full Member
  • ***
  • 46
Re: My SLO Clone Build
« Antwort #35 am: 23.07.2014 09:01 »
Output jacks, impedance selector, and FX loop return wired up. I'm not going to do the slave out. I never use it. And I can always add it later if I want to run wet/dry or something.










*

Offline FourT6and2

  • Full Member
  • ***
  • 46
Re: My SLO Clone Build
« Antwort #36 am: 25.07.2014 09:01 »
So close!

Had to figure out a way to hold the preamp board up off the table, while at the same time keeping the lead I was soldering from falling out since they're installed from the top of the board. That's where these Helping Hands come in handy. Was pretty easy. :)








*

Offline Duesentrieb

  • YaBB God
  • *****
  • 5.810
Re: My SLO Clone Build
« Antwort #37 am: 25.07.2014 09:47 »
Awesome.

The slave out is useful if you want to record thru Torpedo's software. Then you can skip the power amp simulation. Just hook the amp to a load, Mike.

*

Offline darkbluemurder

  • YaBB God
  • *****
  • 2.459
Re: My SLO Clone Build
« Antwort #38 am: 25.07.2014 14:14 »
That's going to be an awesome amp, great build quality.

Is there a particular reason why you used the "purple wiring code"? (just kidding ;D)

Cheers Stephan
Bauten
Chieftain, HoSo56, Cleartone, Dirty Shirley, CJ 11, Junior Chief, Peggy 40

Conversions
Marshall 1959 SLP RI zu Minimalist HRM, Fender Bassman zu Mark Overdrive Special, Marshall 100W JMP zu Fat BE100, Marshall JTM 45 Reissue zu Dirty Daisy; Guyatone Bassman zu Basstonemaster

*

Offline FourT6and2

  • Full Member
  • ***
  • 46
Re: My SLO Clone Build
« Antwort #39 am: 25.07.2014 16:17 »
Purple sounds better!

*

Offline FourT6and2

  • Full Member
  • ***
  • 46
Re: My SLO Clone Build
« Antwort #40 am: 26.07.2014 05:06 »
Got the AC lines, Depth control, loop, and channel switch all wired up. Board is now locked in.










*

Offline FourT6and2

  • Full Member
  • ***
  • 46
Re: My SLO Clone Build
« Antwort #41 am: 27.07.2014 08:44 »
Was out doing real-world stuff for the majority of the day. So did a couple of the small things left to do here and there: Power Board to Preamp Board jumpers for Bias, B+, and Ground; signal coax to V3/7 (not shown); and remote bias control.






*

Offline FourT6and2

  • Full Member
  • ***
  • 46
Re: My SLO Clone Build
« Antwort #42 am: 28.07.2014 04:09 »
Yay, all done! :)

Just gotta do some testing to make sure all the voltages are good. Keeping my fingers crossed.

High Res Version: http://fc08.deviantart.net/fs71/f/2014/208/5/f/slo_clone_1_by_haftelm-d7sk7t6.jpg


*

Offline FourT6and2

  • Full Member
  • ***
  • 46
Re: My SLO Clone Build
« Antwort #43 am: 28.07.2014 05:58 »
Powered up. No smoke, no sparks. Everything seems good. :) I think all the voltages check out for the most part. Some are a bit higher, some lower. Plate voltage is crazy high... 520 volts. Damn. Highest I've seen in any amp.

TARGET:




ACTUAL:


*

Offline Laurent

  • YaBB God
  • *****
  • 2.028
  • Nichts ist unmöglich
Re: My SLO Clone Build
« Antwort #44 am: 28.07.2014 06:58 »
Hi!

Really nice job!! Looks amazing  :topjob:

Waiting for the final test: walls shaking test in the house  ;D

Is the voltage of the PI V5-pin 6 a typing mistake? Should probably be 257.9 instead of 357.9V, right?

Cheers,
Laurent